You are here

10 Shop Organization Ideas

  • 01

    Consolidated Chargers
    Brian McAfee was tired of having the chargers for his electrical tools all in different spots, so he mounted them on a ½-inch piece of plywood along with a power strip to plug the tools into. The plywood hangs in a handy locatio

  • 02

    Welding Items
    To put an end to looking around for his tools while he was welding, Robert Waldner of Platte, South Dakota, fit a 3/16-inch-thick steel strap around his oxygen tank. It’s bolted on with wing nuts for quick removal when it’s time to switch to a new tank. There are hooks welded on for a tape measure, crescent wrench, welder spray, and a welder shield.

  • 03

    Revolving Shop Stand
    The base for this revolving shop stand is a final drive housing found by Bryan Hoersten of Delphos, Ohio, on a worn-out tractor in a salvage yard. He mounted a bench grinder on one side and a wire wheel on the other. It spins 360 degrees, so both pieces of equipment can sit near a wall. He says that with such a heavy base, he doesn’t worry about the unit tipping over.

  • 04

    Rotating Tool Center
    Pieces of 3x3-foot plywood form the exterior surfaces of this tool center built by John Russell of Pemberville, Ohio. It turns 360 degrees on inexpensive casters, but one extra caster is spring-loaded to create a detent that will catch the unit in one of two positions, so the storage rack sits square with the shop.

  • 05

    Hose Caps
    Carson Tardy says they hang their extra hydraulic hoses on the wall to keep them out of the way in their farm shop in Effingham, Illinois. The hoses drip oil making a mess. So before they put a hose away, they cap each end with a pipe cap being careful, of course, to match thread sizes. The floor stays clean, and the hose threads are protected from corrosion.

  • 06

    Hose Reel Mount
    Another idea from Carson Tardy: To protect the replacement for their worn-out power washing hose, they built an extended mounting frame for it. The frame prevents the hose from wear by bringing it out and away from the wall and other nearby obstructions.

  • 07

    Extension Cord Reel
    To create an extension cord reel remove the pour spouts from two 5-gallon bucket lids. Fasten a handle to the center of one lid with one screw so it can spin, and fasten a second handle on the other lid opposite the spout hole. Screw both lids to the ends of a 4x4-inch block to make a spool with the cord going through one spout hole. Thank you to Ed Winfrey of Sibley, Missouri.

  • 08

    Rolling Bins
    Orval Bunger used old bed framing (1.5-inch angle iron) for his shop rack. It sits on 5-inch casters in his farm shop near Upland, Nebraska. Each side holds 60 bins: three rows of 5.5-inch bins and three rows of 6.5-inch bins. The removable ½-inch plywood shelves in the center are for tools and miscellaneous items. The top center holds 10 spray cans.

  • 09

    Torch Stand
    When he needs to heat iron until it’s red hot (for straightening or shaping), Jack Kiser uses this stand he built at his farm in Fremont, Ohio. This is an advantage because if he has to turn off the torch and lay it down, the metal loses some of the heat, which makes it more difficult to form. With both hands free, he holds the metal he’s heating with a locking-type pliers.

  • 10

    Lazy Susan

    Jim Courtright utilized an empty corner by building a lazy Susan organizer at his farm near Hudson, Indiana. It’s made out of the basket from a steel-wheeled hay rake, and the base uses a tire, rim, and spindle. The deburred, sanded shelves are slightly bigger than the supports, and each shelf can hold four 5-gallon pails.

Here are some tips for using all the space inside a farmer's shop

Read more about