Content ID

45628

Not Planting Corn Yet? Is Your Planter Ready? Make Sure With These Tips

Weekend rainfall's likely derailed any plans a lot of farmers in the Plains and Midwest may have had to get much fieldwork done this week. If that's true on your farm, instead of pacing a trough in your office or shop, you can use this time to run a last-minute check on your planter and make sure that when the planting weather window does open up, you're ready to fly through it.

You've read your owner's manual, right? If you're nodding...and telling the truth...it is still important this time of year to make sure you give it at least a good scan and keep it close by as you get ready to roll, especially if you're considering changing settings or making any kind of adjustments, says University of Nebraska Extension ag engineer Paul Jasa. And, do this before you are loaded with seed and hitting the field.

"Before starting to plant, take time to check on how well your planter will perform in the field. As with any piece of equipment, the operator's manual is the starting point for the initial settings and adjustments. Recommendations and trouble-shooting tips are in the manual and also available from others who own and operate similar equipment," he says in a university report. "To check your planter in your conditions, take it to the field without any seed in it and make adjustments to improve its performance. By doing this check before planting, you can save valuable time in the field.

"Make the necessary adjustments or add the required equipment to improve planter performance and check the planter again. Even though a preseason planter check was made, all of these items should be rechecked when actual planting begins and as conditions change during the planting season," he adds.

VIDEO: More Last-minute Planter Tips from Agriculture.com

Jasa also recommends the following 5 steps when conducting your last-minute planter checkup:

  1. Level the planter in the field, making sure that the toolbar is at the proper height and leveled front-to-rear, perhaps even slightly "tail" down. This allows for the full range of movement of the parallel links on the row units, helps keep the planter on the row, and aids in seed-to-soil contact. If the toolbar is too high, the downpressure springs are ineffective. If the toolbar is too low, you may break downpressure springs by over extending them.

  2. Make sure that the planter carrying wheels are exactly centered between the rows and that they are carrying some weight while setting the toolbar height. This is especially important for producers using the ridge-plant system to help keep the planter on top of the ridge.  Remember that the toolbar height will change by the height of the ridges and needs to be reset as the carrying wheels settle into the furrow.

  3. Once the planter is leveled, try blind planting with no seed in the boxes or other products on the planter (everything empty). Stop with the planting units in the ground and check to see if the depth gauge wheels are in firm contact with the soil surface. If they are not, tighten the downpressure springs (or increase the air pressure on the airbags, if so equipped) and try planting again. If you cannot tighten the springs, you may have to add extra springs or add weight directly to the row unit to get the gauge wheels in firm contact with the soil. If you cannot turn the depth gauge wheels slightly, especially on wetter soils, you may have to reduce the downpressure to avoid over-compacting the soil next to the seed-vee.

  4. Check to see if you can slip the seeding mechanism drive wheels as the downpressure springs will be lifting the toolbar. You may have to add weight to the planter frame for the springs or airbags to work against and to keep the drive wheels firmly on the ground to reduce slip. Don't loosen the springs to get the drive wheels back in contact with the soil as penetration to seeding depth is necessary. Extra weight will be needed for dry soils or heavy residue and on planters with inter-plant units.

  5. Place a small amount of seed into a couple of seed boxes and plant a short distance. Check seeding depth, seed-to-soil contact, seeding depth uniformity, and seed spacing uniformity. Evaluate seed-vee closing and check to make sure you're not over compacting the seed zone or packing below the seeding depth.


927861f4b2b8f3a219683dbfb8f844ba_clientI

Published: 4/20/2015
The planting weather's far from perfect in much of corn country as mid-April nears. But, don't waste the delay time pacing the floor and just wishing for better weather. Now's a good time for a last-minute run-through of your planter to make sure it's all ready to roll.

3368d43087946d44a362672f1ceaf3cc_clientI

Published: 4/20/2015
It's spring planting season! Is your iron up to snuff? If you need to conduct some last-minute maintenance, or need a new planter altogether, here are some of the latest planter features from the Agriculture.com Machinery Team.

56e7794c1a14c54f5d6b4dc5e78cd911_clientI

Published: 4/20/2015
Is your planter ready to go this spring? Here's a quick checklist for you to run through before you get your planter in the field and loaded up, courtesy DuPont Pioneer. Level the Planter. Check the hitch height. The tractor hitch height may vary due to the tractor tire size, tractor manufacturer, and the type of planter (Draw bar vs.

c34715e5c72d5257685ddaa9377c3ffa_clientI

Published: 4/20/2015
Is your planter ready for spring? Check out these tips before you roll.

dedcea1c8003e8e7a515d26e0635b74a_clientI

Published: 4/20/2015
A corn planter set properly can have a dramatic impact on stand establishment, according to agronomist Matt Hagny.

Read more about
Loading...

Talk in Marketing